NEWS & ENGINEERING
PCB · PCB ASSEMBLY · DESIGN · PROCUREMENT AND ACCEPTANCE
Opening Gerber graphics does not establish complete manufacturing semantics. This article organizes delivery checks by layer function, drilling, units, polarity, and coordinates. 6-layer mapping and unit-ratio examples explain ambiguities, followed by independent-viewer review, netlist cross-checking, and revision freezing.
Read ArticleIntermittent USB disconnections require joint checks of supplies, connectors, differential channels, cables, and driver logs. End-to-end component tables, rate/throughput examples, and reproducible cross-test matrices distinguish evidence from enumeration, sustained transfer, and signal-quality testing, with methods for layer-transition, ESD, and supply faults.
Read ArticleThe AM437x TIDEP0012 design without VTT applies only with short routes, no more than two DDR3 devices, and balanced-T topology. This article provides porting differences, a 400 MHz timing-unit example, stackup/configuration checks, and memory stress records, explaining why copied lengths or successful startup do not establish adequate timing margin on a new board.
Read ArticleLink each manufacturer change or discontinuance notice to the affected part numbers, product revisions, stock and inbound orders. Assign technical evaluation, purchasing milestones and old/new lot identification before approving the transition.
Read ArticleCheck the evidence behind component sources, complete part numbers, packaging condition and receiving records. Define lot traceability, consigned and procured responsibilities, and exception handling without treating label appearance or one functional test as proof of authenticity.
Read ArticleTPS22918 rise time must meet inrush, supply-droop, and downstream-startup requirements together. CT approximations, capacitor charging, and conduction-drop examples support enable/input/output/discharge timelines and verification of rapid restarts, backfeeding, and current ratings.
Read ArticleTPA3116D2 output power requires supply, load, distortion, and thermal conditions together. A 20 W load example explains BTL/PBTL connections, top-side PowerPAD cooling, filtering, and mute timing. Power/distortion, noise, temperature, and harness verification tables help diagnose noise floors, pops, and protection abnormalities.
Read ArticleLM3409 is an external-PFET buck LED controller; power stages and strings jointly determine output capability. This article distinguishes ordinary/HV input ranges, uses peak-current/shunt examples to explain average brightness and ripple, and provides dimming comparisons, flicker diagnosis, and waveforms for low brightness, startup, and thermal checks.
Read ArticleIWR6843 mmWave performance depends on antennas, supply, chirp configuration, installation, and algorithms. Range-resolution, beat-frequency, and raw-data examples support parameter tradeoffs and scenario verification, distinguishing echoes, correct ranging, and application detection. Ordinary and antenna-in-package variants cannot directly share layouts.
Read ArticleDRV8876 recommended operating voltage is 4.5–37 V; 40 V is not a continuous operating range. This article explains IPROPI current mirrors, VREF, and regulation thresholds. Feedback-resistor examples and sampling-timing tables distinguish drive, brake, and coast, with protection, regeneration, and thermal records supporting reproducible current assessment.
Read ArticleDRV8833 current capability depends on package and peak/continuous conditions; dual-H-bridge control also involves braking, coasting, and current regulation. Shunt/conduction-loss examples, control-state tables, and startup/stall waveforms explain supply resets, protection triggers, and thermal issues, defining verification scope for actual motors.
Read ArticleCC1101 bands, crystal, matching network, antenna, and registers must form one configuration. Frequency-word and transmit/receive-duty examples support band tables and conducted/over-the-air test sequences, separating frequency offset, packet errors, and power consumption. Chip band coverage does not establish end-product authorization.
Read ArticleFrom fabrication files and PCB structures to assembly, material supply, design, and acceptance. Choose a category by service or open a specific topic from the illustrated list.
Compare PCB fabrication, PCB assembly, and electronics design. For a specific decision, browse the engineering topic library. Project files, standards, and acceptance conditions govern the engineering review.
Tell us the product use and which files are available. We can define the next engineering step even when the data package is not complete.
